Fix (APAR): PM34957 Status: Fix Release: 7.0.0.17 Operating System: AIX,HP-UX,IBM i,Linux,Solaris,Windows Supersedes Fixes: CMVC Defect: PM34957 Byte size of APAR: 25426 Date: 2011-06-01 Abstract: The server sends out an INVITE from one local port, followed by a CANCEL from a different local port. Description/symptom of problem: PM34957 resolves the following problem: ERROR DESCRIPTION:? Product Version: 7.0.0.13 OS and Additional Information: Linux, version 2.6.18-194.17.4.el5 A Session Initiation Protocol (SIP) application cancels a pending INVITE request. The SIP Container immediately responds on this request with a 200 OK response. However, after that, the SIP Container should generate a new CANCEL request and send it to the client. The CANCEL request is rejected with a 430 error. LOCAL FIX:? None PROBLEM SUMMARY:? USERS AFFECTED: Session Initiation Protocol (SIP) users of IBM WebSphere Application Server V7.0 PROBLEM DESCRIPTION: The server sends out an INVITE from one local port, followed by a CANCEL from a different local port. RECOMMENDATION: None The problem occurs in an environment where the SIP container is listening to two (or more) different ports over the same network protocol. The application sends out an INVITE request, and then sends out a CANCEL. Because of a bug in the SIP container, each request is being sent from a different local port. PROBLEM CONCLUSION:? The problem is fixed in the SIP container. With this fix, the CANCEL is sent from the same local port as the INVITE. The fix for this APAR is currently targeted for inclusion in fix pack 7.0.0.19. Please refer to the Recommended Updates page for delivery information: http://www.ibm.com/support/docview.wss?rs=180&uid=swg27004980 Directions to apply fix: Fix applies to Editions: Release 7.0 __ Application Server (Express or BASE) _X_ Network Deployment (ND) __ Edge Components __ Developer Install Fix to all WebSphere installations unless special instructions are included below. Special Instructions: None NOTE: The user must: * Logged in with the same authority level when unpacking a fix, fix pack or refresh pack. * Be at V7.0.0.0 or newer of the Update Installer. Certain iFixes may require a newer version of the Update Installer and the Update Installer will inform you during the installation process if a newer version is required. This can be checked by reviewing the level of the Update Installer in file /updateinstaller/version.txt. The Update Installer can be downloaded from the following link: http://www.ibm.com/support/docview.wss?rs=180&uid=swg21205991 1) If your iFix is delivered as a single file with a .pak extension, Copy the .pak file directly to the maintenance directory. If your iFix is delivered as a single file with a .zip extension, unzip the file into the maintenance directory. 2) Shutdown WebSphere Application Server. Manually execute setupCmdLine.bat in Windows or . ./setupCmdLine.sh in Unix from the WebSphere instance that maintenance is being applied to. 3) For IBM i users, use the update command to install and uninstall the interim fix. The IBM Information Center can provide additional details, if needed, on the use of this command. http://www14.software.ibm.com/webapp/wsbroker/redirect?version=compass&product=was-nd-iseries&topic=rins_update. For non-IBM i users, launch the Update Installer and click the Next button on the Welcome page. 4) Enter the directory path of the installation location of the WebSphere product you want to update, and click the Next button. 5) Select the "Install maintenance package" operation and click the Next button. 6) Enter the directory path of your maintenance directory where you have the maintenance packages (.pak files) and click the Next button. 7) The Available Maintenance Package to Install page should list all maintenance packages (.pak files) that it finds in the directory path provided in the previous step. The Update Installer will select the correct maintenance packages based on your system configuration and will not allow an invalid combination to be installed. Please keep the Update Installer recommendations and click the Next button and continue with the installation of the maintenance package. To determine why some maintenance packages have been identified as not applicable, see description in log found in /logs/tmp*/updatelogs.txt 8) For all platforms except Windows. In pre-install summary panel, use the "verify permission" feature to verify the user has permissions to apply updates to files associated with the selected maintenance. Correct any file permissions before clicking next to start the install. 9) Restart WebSphere Application Server. Directions to remove fix: NOTE: * The user must have Administrative rights in Windows, or be the Actual Root User in a UNIX environments. * FIXES MUST BE REMOVED IN THE ORDER THEY WERE APPLIED * DO NOT REMOVE A FIX UNLESS ALL FIXES APPLIED AFTER IT HAVE FIRST BEEN REMOVED * YOU MAY REAPPLY ANY REMOVED FIX Example: If your system has fix1, fix2, and fix3 applied in that order and fix2 is to be removed, fix3 must be removed first, fix2 removed, and fix3 re-applied. 1) Shutdown WebSphere Application Server. Manually execute setupCmdLine.bat in Windows or . ./setupCmdLine.sh in Unix from the WebSphere instance that uninstall is being run against. 2) Start Update Installer 3) Enter the installation location of the WebSphere product you want to remove the fix. 4) Select "Uninstall maintenance package" operation. 5) Enter the file name of the maintenance package to uninstall (PKxxxxx.pak). 6) UnInstall maintenance package. 7) Restart WebSphere Directions to re-apply fix: 1) Shutdown WebSphere Application Server. 2) Follow the Fix instructions to apply the fix. 3) Restart WebSphere Application Server. Additional Information: