|
DB2 Change Accumulation Tool Version 1.4
|
|||||
| APAR | CLOSE DATE |
PTF(s) | Fixing APAR if PE |
HIPER? | Abstract |
|---|---|---|---|---|---|
2010 |
ABEND=S000 U1000 REASON=00000000 ON GGC#MAIN EXTERNAL SYMPTOM CODE | ||||
2010 |
ABENDU0012 IN MODULE GGC#LRD6 / GGC#MAIN | ||||
2010 |
ABEND U1000 OR U0012 ON GGC#LGAP, GGC#MAIN AND FAILS WITH A MESSAGE GGC1803I | ||||
2010 |
DB2 CHANGE ACCUM MINILOG SHARELEVEL CHANGE MAY CAUSE DATA CORRUPTION | ||||
2010 |
USER ABENDU0012 ON LMOD'S GGC#LRD6 OR GGC#LRDR 10/02/23 PTF PECHANGE |
||||
2009 |
ABEND=S04E U0000 REASON=00E40347 ON A REBUILD INDEX AFTER GGC WTV | ||||
2009 |
HANDLE SORTS BETTER WHEN DSNUM 0 IMAGE COPIES BEING USED FOR MULTIPLE SINGLE PARTITIONS SELECTED VIA CO 09/12/14 PTF PECHANGE |
||||
2009 |
ABEND S0C4, REASON CODE=00000011 ON NAME=GGC#MAIN OR MINI LOG JOB MAY NOT CREATE A MINILOG DATASET WHEN CHECKPOINT CONTAINS | ||||
2009 |
ABEND=S000 U1001 REASON=00000000 ON GGC#MAIN | ||||
2009 |
ENABLE THE ABILITY TO SPECIFY AN END POINT (RBA OR LRSN VALUE) FROM SYSCOPY (START_RBA) THAT IS OF ICTYPE 'Y' OR 'S' OR 'W' | ||||
2009 |
REBUILD INDEX MAY NEVER COMPLETE OR SELECT ON TABLE MAY GIVE -904 AFTER A GGC WTV ON A SINGLE PARTITION, OF A PARTITIONED TS |
||||
2009 |
CODE OPTIMIZATION | ||||
2009 |
GGC1021I THE TO_QUIESCE CONTROL CARD WAS SPECIFIED, BUT NO QUIESCE POINT(S) WERE FOUND. | ||||
2009 |
POSSIBLE DATA CORRUPTION ON IMAGE COPY OR WRITE_TO_VSAM, WHEN DB.TS IS IN AREO* STATUS DUE TO AN ALTER | ||||
2009 |
CHANGE ACCUMULATION TOOL CAN CAUSE DATA CORRUPTION WHEN RESTORE_BEFORE CONTROL CARD IS USED | ||||
2009 |
RECOVERING A 32 KB PARTITIONED TS, FAILS WITH A MESSAGE GGC1802I | ||||
2009 |
LOSS OF DATA MAY OCCUR IN DB2 CHANGE ACCUM WHEN THE SEGMENTED TABLE SPACE HAS 3 EXTENTS | ||||
2009 |
ALLOW USER TO PRE-ALLOCATE SORT FILES. | ||||
2009 |
DYNAMIC ALLOCATION RETURN CODE = 02200004 | ||||
2009 |
POTENTIAL LOSS OF DATA WHEN MIXING GROUP LEVEL AND SPACE LEVEL MINILOGS FOR AN OBJECT IN A SINGLE IMAGE COPY CREATION RUN. | ||||
2009 |
BYPASS LOG RECORD TYPE "REDO", SUBTYPE "LGOPWHLR" WHEN PROCESSING MINILOGS | ||||
2009 |
ADD GGCALA TO PTF. | ||||
2009 |
ROLLUP APAR | ||||
2008 |
GGC2109I TAPE DATASET COULD NOT BE CATALOGED STARTING WITH LABEL=2 WHEN ALLOCATING MULTIPLE GDG ON A TAPE STACK. | ||||
2008 |
ROLLUP APAR FOR INTERNAL CHANGES | ||||
2008 |
OBJECT PROFILE NOT FOUND IN SEARCH AFTER SAVING SUCCESSFULLY ANDCREATE OBJECT PROFILE WITH THE SAME NAME GIVES A MESSAGE THAT | ||||
2008 |
GGC$OPRE PANEL DOES NOT GIVE AN ERROR MESSAGE ON F3 INSTEAD OF ENTER, WHEN INVALID VALUE IS ENTERED FOR ANY UNPROTECTED FIELDS. |
||||
2008 |
ABEND 113000 HEX OCCURRED PROCESSING COMMAND 'GGC$MAIN' ON AN IMPORT/EXPORT PROCESSING AND AN INVALID DATASET NAME IS USED | ||||
2008 |
MINI LOG DATASET MAY BE TRUNCATED WHEN THE LOG READ PROCESS GETSA B37 WHILE WRITING TO MINI LOG DATASETS OR SORT INPUT FILE. | ||||
2008 |
ERROR MESSAGE " GGC2109I THE FOLLOWING TAPE DATASET COULD NOT BE CATALOGED" WHEN ALLOCATING A GDG. | ||||
2008 |
ABILITY TO SPECIFY VOL COUNT, WHEN DEFINING CHANGE ACCUMULATION IMAGE COPY DATASET GENERATION PARAMETERS | ||||
2008 |
ABEND=SC40 U0008 REASON=00000000 ON GGC#MAIN, OFFSET=0000046A MAY OCCUR ON A GGC IMAGE COPY GENERATION. | ||||
2008 |
PANEL 'GGC$DELO' ERROR (PANEL NOT FOUND), WHEN TRYING TO DELETE AN OBJECT PROFILE DISPLAY FROM GGC$OPRU PANEL | ||||
2008 |
DYNAMIC ALLOCATION RETURN CODE = 02200004, WHEN READING FILES OUT OF SEQUENCE WITHIN A MULTIPLE VOLUME SEQUENCE | ||||
2008 |
DYNAMIC ALLOCATION/CONTROL CARD BASED OUTPUT FULL IMAGE COPIES EXCEEDING 20 TAPE VOLSERS FOR A SINGLE DATASET CAN GET AN S0C4. |
||||
2008 |
SQLCODE206 MAY OCCUR ON PROGRAM GGC#SCPY WHEN PERFORMING A 'BUILD' JOB PROFILE | ||||
2008 |
ABEND=S000 U1000 IN GGC#MAIN ON A GGC IMAGE COPY GENERATION. | ||||
2008 |
PERFORMANCE ENHANCEMENT WHEN WORKING WITH MINILOGS WITH LARGE AMOUNTS DATA. | ||||
2008 |
POSSIBLE ISSUE WITH EXPIRATION_DATE NOT SET CORRECTLY ON DYNAMICALLOCATION OF DATASET | ||||
2008 |
ABEND S0C4 ON ISPMAIN, OFFSET=000022D8 MAY OCCUR ON IMPORT UTILITY PROFILE | ||||
2008 |
MINI LOG DATASET NOT CREATED ON A PARTITIONED TABLE SPACE THAT HAS MORE THAN 254 PARTITIONS. | ||||
2008 |
" I "MPORT LINE COMMAND ON UTILITY PROFILE AND JOB PROFILE IS SOMETIMES REJECTED | ||||
2008 |
CHANGE ACCUMULATION TOOL V1.4, ABEND=S000 U0008 REASON=00000000 | ||||
2008 |
GGC V1R4 ONLINE HELP PANEL AND MESSAGE UPDATES | ||||
2008 |
"I"MPORT LINE COMMAND ON OBJECT PROFILES IS SOMETIMES REJECTED | ||||
2008 |
ON INVALID VALUE, THE POPUP ERROR MESSAGES GGC055E , GGCM318E APPEARS ON TOP OF THE FIELD AND BLOCKS EDITING THE FIELDS. | ||||
2008 |
GGC1012I NO VALID FULL IMAGE COPY IN THE SYSCOPY HISTORY WAS FOUND FOR SPACE(S) | ||||
2008 |
S0C4, REASON CODE=00000004 ON GGC#LRD6 WHEN USING ABOVE_THE_BAR KEYWORD AND GGC1503I IN DB2 CHANGE ACCUM JOB OUTPUT. | ||||
2008 |
POSSIBLE PROBLEM WHERE CHANGE ACCUM WOULD REREAD DB2 LOG RANGES AND DUPLICATES THEM ONTO SUCCESSIVE MINILOG DATASETS. | ||||
2008 |
SORTWORK DD NOT GENERATED WHEN SORT WORK SPACE OPTIONS SETUP ON GGCPNL3 OR GGC$JOVR | ||||
2008 |
SCROLL RIGHT DOES NOT WORK ON GGC$OPRE AFTER EXIT FROM THE PANELAND RE-ENTER INTO THE PANEL | ||||
2008 |
SQLCODE -904 MAY OCCUR WHEN RUNNING PARALLEL CHANGE ACCUM JOBS. | ||||
2008 |
VIEW/ UPDATE ON A UTILITY PROFILE THAT IS SETUP FOR WRITE MODE 'V' TURNS THE UPDATE UTILITY OPTION TO 'Y' FOR THE IMAGE COPY | ||||
2008 |
SKIP ALL CHECKPOINT PROCESSING IF THE CURRENT RUN IS WRITE_TO_VSAM, TO_CURRENT. | ||||
2008 |
ALLOW OPTION TO CONDITIONALLY REMOVE THE RECOVER PENDING FLAG ONSPACES THAT ARE WRITTEN TO WITH A WRITE_TO_VSAM OPERATION | ||||
2007 |
POSSIBLE INVALID RECORD COUNT WHEN USING UNLOAD FROM A DB2 CHANGE ACCUM IMAGE COPY. | ||||
2007 |
PERFORMANCE IMPROVEMENT AND 64 BIT STORAGE SUPPORT FOR INTERNAL DATA STRUCTURES. | ||||
2007 |
ADD ABLILITY TO ALLOW SHRLEVEL CHANGE MINI LOGS AND TO NOT CHECKFOR TRANSACTION CONSISTENCY FOR WRITE-TO-VSAM ON A RECOVERY TO |
||||
2007 |
SAME RANDOM NUMBER FOR LP AND LB DATASETS, WHEN GGC BUILDS A JCLWITH CONTROL CARDS FOR LP, LB, RP, RB | ||||
2007 |
DUPLICATE DATASET NAMES NOT RECOGNIZED WITH IC_XX CONTROL CARD AND GDG DATASET | ||||
2007 |
OUT OF SYNC CONDITION BETWEEN THE COPY AND DATA IN THE TABLE ON USING GGC WRITE_TO_VSAM TO AN END_RBA OF A PREVIOUS IMAGE COPY |
||||
2007 |
CHANGE READING OF MINI LOGS FROM SORT PHASE TO MERGE PHASE | ||||
2007 |
ABEND0C4-11 IEFQB551+7340 RUNNING DB2 CHANGE ACCUMULATION | ||||
2007 |
NEW CONTROL CARD ADDED TO ENHANCE THE RETURN CODE FUNCTIONALITY OF MIS-MATCHED RBAS IN GROUPS WHERE THE DETERMINED RBAS WIND UP |
||||
2007 |
END POINT RECORDED MAY NOT MATCH THE SPECIFIED END POINT WHEN END_LRSN OR TOLOGPOINT CONTROL CARDS ARE USED. | ||||
2007 |
POSSIBLE CORRUPTION OF NEW IMAGE COPY DUE TO INVALID IMAGE COPY STARTING POINT SELECTION, | ||||
2007 |
INCOMPLETE CHANGE ACCUM IMAGE COPY WITH A RC=0 ALSO DUPLICATE OUTPUT IMAGE COPY DATASET CHECKING SYSCOPY | ||||
2007 |
WRITE TO VSAM OPERATION MAY FAIL IF VSAM DATASET IS DELETED | ||||
2007 |
ABEND=S002 U0000 REASON=00000018 ON MINI LOG GENERATION WHEN MINI LOG CONTROL CARDS ARE SPECIFIED AT SPACE LEVEL | ||||
2007 |
MODIFY THE MINILOG PROCESS TO NOT INCLUDE ANY CHECKPOINT ACTIVITIES IN THE MINILOG DATASET WHEN MINI LOG CONTROL CARD IS |
||||
2007 |
DB2 CHANGE ACCUM LOOPING WITH LARGE NUMBER OF OBJECTS | ||||
2007 |
S0C1 ABEND MAY OCCUR WHEN END_RBA UNIFIED KEYWORD IS USED WITH Z/OS VERSION PRIOR TO V1.8 | ||||
2007 |
SQLCODE -805 ON PACKAGE GGC#XMLC WHEN PERFORMING A ' BUILD ' JOBPROFILE FROM A DB2 V9 SYSTEM | ||||
2007 |
ON A GGC IMAGE COPY WHEN TOLOGPOINT CONTROL CARD IS SPECIFIED ATGROUP LEVEL, THE GGC IMAGE COPY ABENDS WITH U0008 | ||||
2007 |
USER ABEND 1000 IN GGC#MAIN CSECT GGC#LGAP AT + X'954E' | ||||
2007 |
S0C4 IN GGC#LGAP | ||||
2007 |
GGC2633I THE IC_SPACE PARAMETER SPECIFIED IS INVALID. | ||||
2007 |
ADD ABILITY TO USE THE UNIFIED PARAMETER WITH END_RBA , END_LRSN, AND TO_LOGPOINT CONTROL STMTS | ||||
2007 |
PANEL GGC$VIMG "TAKE IMAGE COPY" FIELDS LP, LB, RP, RB ARE SPACES AND DO NOT SHOW THE VALUES UPDATED FROM GGC$UIMG | ||||
2007 |
ABEND 0C4-11 MAY OCCUR IN GGC#MAIN WHEN CREATING AN IMAGE COPY | ||||
2007 |
ABENDU1007 GGC#CHKR+86A WHEN TRYING TO GENERATE MINI LOGS | ||||
2007 |
RBAS CAN BE RECORDED INCORRECTLY WHEN END_RBA IS USED 07/04/26 PTF PECHANGE |
||||
2007 |
CLARIFICATION OF COMMENTS IN THE GGC BIND AND DDL SAMPLES | ||||
2007 |
GGC V1R4 ONLINE HELP UPDATED | ||||
2007 |
VALUES FOR DATA, STORAGE AND MANAGEMENT CLASS SPECIFIED ON GGC$UCPO PANEL ARE MIXED UP WHEN JOB PROFILE IS BUILT. | ||||
2007 |
GGCPROC MEMBER IN SAMPLIB DOES NOT HAVE A INFOM DD | ||||
2007 |
GGC IMAGE COPY WITH CONTROL CARDS DOES NOT CREATE CORRECT COPY WHEN THE END POINT OCCURS BEFORE A DB2 IMAGE COPY | ||||
2007 |
ACCEPT MINI LOG DATASETS AT SPACE() LEVEL IN ADDITION TO GROUP()LEVEL | ||||
2007 |
U1000 ABEND IN GGC#MAIN | ||||
2007 |
AE PK31334 | ||||
2007 |
WHEN A VALID END_RBA IS SPECIFIED ON THE CONTROL CARD GGC WOULD USE THIS RBA AS AN END POINT FOR THE GGC IMAGE COPY. | ||||
2007 |
MISSING MESSAGE FOR GGC073 MESSAGE | ||||
2007 |
WHEN THE SCREEN NAME AND PANELID IS TURNED ON, THE PANELID IS NOT DISPLAYED ON SOME PANELS | ||||
2007 |
SUPPORT FOR DB2 V9 - THE APAR PROVIDES SUPPORT FOR THE FOLLOWINGFEATURES: | ||||
2007 |
DB2 CHANGE ACCUMULATION TOOL V1R4 ONLINE HELP REVISIONS | ||||
2007 |
GGC V1R4 MESSAGE REVISIONS | ||||
2007 |
ABEND U0012 AT LOAD MODULE GGC#LRDR | ||||
2006 |
MESSAGE IKJ56241I FOR FILE ISPWRK1 MAY BE ISSUED WHEN BUILDING JOBS | ||||
2006 |
ABENDU1001 IN GGC#MAIN PROCESSING CHANGES | ||||
2006 |
TO_QUIESCE, TO_QUIESCE(#N) TO RETRIEVE MOST RECENT OR ASSOCIATEDQUIESCE POINT'S RBA. | ||||
2006 |
SQLCODE805 ON A 'BUILD' JOB PROFILE FROM A DB2 V8 SYSTEM | ||||
2006 |
IEW2456E ERROR WHEN APPLYING PTF UK13872 ALONG WITH OTHER GGC PTF'S | ||||
2006 |
ABEND U0008, WHEN READING FILES OUT OF SEQUENCE WITHIN A MULTIPLE VOLUME SEQUENCE | ||||
2006 |
OPTION TO ALLOW OVERRIDE OF SYSPRINT DD | ||||
2006 |
OPTION TO BYPASS SYSLGRNX PROCESSING | ||||
2006 |
INCREASE THE NUMBER OF OBJECTS HANDLED FROM 5,000 TO 20,000 | ||||
2006 |
WHEN NO PROFILES EXIST ON PANELS GGC$OPRD, GGC$UPRD, GGC$JPRD THEN SHOW THAT 'IMPORT' AND 'CREATE' ARE THE LINE ITEM OPTIONS. |
||||
2006 |
LOG READER PERFORMANCE ENHANCEMENTS | ||||
2006 |
MINI LOG PROCESSING CAN SKIP A VALID MINI LOG | ||||
2006 |
DB2 LOG READ TRUNCATION OCCURS WHEN ACTIVE LOG SWITCHES AFTER BSDS IS READ | ||||
2006 |
UTILITY HELP PANEL GGCHUPLK REFERS TO OBJECT PROFILES INSTEAD OFUTILITY PROFILES | ||||
2006 |
SORT ORDER A DOES NOT SORT ON GGC$JPRU PANEL | ||||
2006 |
MESSAGE GGC1161I ISSUED INCORRECTLY | ||||
2006 |
SAMPLIB MEMBER GGCRCALL IS MISSING | ||||
2006 |
INCORRECT UPGRADE OF SHARELEVEL CHANGE TO REFERENCE WHEN IN-FLIGHT THREAD AGAINST A PART OF A PARTITIONED SPACE | ||||
2006 |
SQLCODE -502 WHEN DEFINE CLUSTER (S) FOR MULTIPLE TABLESPACES | ||||
2006 |
ADD ABILITY TO PRIORITIZE THE LOG DATASETS AND IMAGE COPIES SELECTED FOR PROCESSING | ||||
2006 |
DUAL MINILOG GENERATION | ||||
2006 |
ABILITY TO DO A DEFINE CLUSTER AUTOMATICALL IF THE UNDERLYING DATA SET IS NOT FOUND | ||||
2006 |
GGC2402I MEESAGE WHEN WRITE_TO_VSAM FOR A PART OF A PARTITIONED SPACE | ||||
2006 |
INVALID GGCM237I & GGC013I MESSAGES WITH FORM COMMAND AND SELECTED | ||||
2006 |
INVALID UTILITY PROFILE IS SELECTED WITH FORM COMMAND | ||||
2006 |
S0C4 WHEN DELETING A UTILITY PROFILE WITH SCREEN SIZE OF 24X80 | ||||
2005 |
CHANGE ACCUM V1.4 ROLLUP APAR | ||||